Ford A Speed Technology, Members Have/Want page

Do you have something that you don't want? Do you want something that you don't have?
Ads will be dated and run for three months unless otherwise informed

Top-loader used tranny parts
78-7006 (caustic soaked, glass bead blasted, Magnafluxed and painted black. Thrust surface is perfect.) $82
48-7561 Clutch release bearing hub (1.753" ID. Has some wear where fork contacts pads)
78-7050 Front bearing retainer (1.743" OD)
81A-7105 Synchro hub (w/ good 81A-7069-B thrust washer) $15
48-7518 Inspection cover (blasted & painted black) $15
B-7090 U-joint (w/ bolt & washer. No slop) $43
??-7231 (1st/Rev. shifter fork with used pin from 81A-7222 housing) $12
81A-7240 Shifter shaft – 1st/Reverse $6
81A-7241 Shifter shaft – 2nd/High $6
74-7238 Shifter detent ball, spring, plug - 2 sets plus bullet $22
B-7115 Cluster gear spacer tube $3
B-7155 Counter shaft lock pin $3
??-???? (1950 side shift fork & paddle) $20/pair
Plus shipping from 27344
James Andrews 919-742-7438 jea777@peoplepc.com

C Crank (integral counterweights), hot-tanked and magnafluxed clean - $300
B connecting rod set (4) hot-tanked and magnafluxed clean - $75
Mallory YC distributor, two piece cap w/new points/rotor/condenser - $175
Packard Ignition wire (black) with RAJO plug ends - $25
Harvey Crane “¾ Race cam”, specs on request - $125
Exhaust Header flange, thick steel! - $20
Lincoln Zephyr Carb (small noogie on air horn lip) w/rebuild kit - $60
Cal Custom Chrome Air Cleaner, NOS w/wire mesh element - $20
Cal Custom Chrome Air Cleaner, excellent, small cutout for linkage - $15
Clutch/Brake pedals with heavy offset to clear lowered/custom body - $15
1934 front axle, drilled, 4” drop - $175
18” wheels, set of five, nice vintage orange color powdercoat, plain center caps - $250
Dual Brake cylinder, NOS for early 70’s Ford truck
Jack, vintage, probably truck - $10
Forged Buggy steps - $10
1920’s Studebaker “torpedo” cowl lamps, cleaned and primed - $75/pair
1946/48 Chrysler “spider web” tail lights, cleaned and primed - $200/pair
Vintage Mallory ignition coils(two), probably bad, but look cool - $15 each
1930’s Cadillac individual tilt-back seat frames - $20/pair

Stuart England San Jose, CA, 95125 408-316-6185 (Mobile) qikmerc@netzero.net

FOR SALE

Cast aluminum timing cover for model a and b ford. Available with or without adjustable silicon bronze cam button. Accepts all stock oil seals and generator/alternator. Perfect for precise cam location in a pressurized hi performance engine and equally at home polished for a show engine, Please email for pics. $250 amsando@socal.rr.com

Complete HAL Engine, (2) B Engines with no cracks and other B engine parts
Paul St Louis, MOe-mail pganninger@msn.com

I'm looking for a four port cross flow head to run on my "B" engine with roller lifters and cam.
Denny Sprecher, Salt Lake City, Utah - (801) 282-8005

1927 T block, counter balanced A crank drilled for oil. A cam, main caps, hi top pistons. Timing gear by Dan McEarchern. A rods with inserts. Side drive dist. And oil pump, 6 cyl Chrysler, full flow oil filter. Rajo cross-flow head, log intake manifold with two "81" carbs. A housing to ‘27 block, lightened A flywheel and A trans. T frame, suicide front axle, T and brass radiator "15". $5975.00
Les Cash, Carson City, NV. 775-246-0648. Call for list of parts not listed for this "T" - "A" project.

AA Ford fender. Right Rear. Originally could have come off of the follow AA trucks: Flatbed (were taken off because they were in the way while loading), hearse, panels and an Express. Looking for a friend in MN. Any assistance appreciated.
Alan Wernstrum - Phone: 707-824-2882

1932/34 Model B crankshaft, commonly referred to as a Model C crankshaft.
Ken Holland Tele: 907 333-3889 or email doris.holland@gci.net

'28 PICKUP ROADSTER, B Engine, Barn Fresh Original Runner/Driver
Needs seat and upholstery. Rough condition but not rusted out. -- $9500
DANN JURGENS - 303-756-0309 - Email: pdjurgens@aol.com - Centennial, CO.

1929 Tudor, low mileage on older restoration, Wes Cooper built engine, new upholstery, good tires, $11,000 OBO.
Marty Clampitt, 530-478-5931 Nevada City, Ca.

Chevy disc wheels, including rims, in good usable condition, for Model T speedster project. T hubs pressed in would be nice, but not necessary.
Jeff - Email at jsa3@wildblue.net

Good original Miller overhead valve head, cast iron preferred. Let me know what you have and how much you want,
Jack Richard jrichardwa@comcast.net

Bell housing "Scatter Shield" for Model A, new or good used.
E-mail: 32roadster@cox.net

I have several Winfield carbs and & parts for sale. When responding, please refer to item number.

Item    Description
  1.        A Updraft       Throttle Body – 6571     Fuel bowl- AU7988   S model $285.00
  2 & 3. A Downdraft Throttle Body – 1901    Fuel bowl – AD2144 SR Model
             A Downdraft Throttle Body – 1902    Fuel bowl – AD2143 SR Model $1200.00
            Note that carbs 2 & 3 are sequentially numbered and will only be sold as a pair.
  4.         AA Updraft     Throttle body – 824X01 Fuel bowl – AU10877 S model $290.00
  5.         B Downdraft    Throttle body – 3605     Fuel bowl – SBD2969 S model - $320.00
  6.         B Downdraft    Throttle body – 1343     Fuel bowl – SBD6039 S model - $320.00
  7.         B Downdraft    Throttle body – 4112     Fuel bowl – SBD8212 S model - $320.00
  8.         M Model Winfield. 2 ¼ “ throttle barrel valve, Ser – 8316 - $225.00
           Bolt mounting spacing 3”, air filter mounting flange has small portion broken away. Very fixable.
  9.         Interesting tube type manifold for M carb listed above - $75.00
           For some reason, the Manifold flanges were cut off. Still quite usable.
10.       Winfield Air Silencer. - $150.00
           Looks like large softball. Air inlet approximately 2” dia, carb inlet approximately 1 ¾” dia. Carb inlet has small
           portion broken away. Very fixable.
11.       Twin mounted AA’s on single base.
           Throttle body – SRAA617        Fuel bowl SRAD546
         Throttle body – SRAA616        Fuel bowl SRAD545 - $1750.00
           Note that the throttle and fuel bodies are sequentially numbered. Both carbs run off a shared fuel inlet line and
           throttle shaft.

All prices are subject to some negotiation and shipping is not included. Pictures are available upon request by item number. Please contact me at DandM_Racing@msn.com for any questions.

1929 BOATIAL SPEEDSTER
CHATTANOOGA 2007 HILL CLIMB RESULTS: Car 16 Class SP-1 - E.T. 10.43 - MPH 51.37

Engine A NOS diamond block, fully inserted pressurized mains, Chevy pistons, counter weighted crank, lightened flywheel, balanced, v8 clutch, Zepher intake, 2 Ford 97 carbs, Reds header, ported and polished, oversized intake 1.730, Weiand 9-1 head, 12 volt ALT.
Frame 29 Ford stock.
Front End Stock, shocks and mechanical brakes, 21” wheels, F-1 steering
Rear End Stock, shocks and mechanical brakes, 4.11, 34 Ford 17” wheels.
Transmission 39 Ford.
Body Hand fabricated, all steel.
Price Asking $22,500
Contact Greg Deal (828) 390-9681 Email: cruisinmamma@charter.net

WANTED

We need 3 Winfield carbs that appear to be sidedrafts. Please review the photo for type.
Contact: Matt Jones - EMAIL: matteo@reoriginals.com

Adapter to fit Vertex Scintilla magneto to Model B block/head, or drawing/photo to manufacture same. Thanks for any help.
Contact: David B. - Email: twofordcoupes@optusnet.com.au

Looking for information on an old hot rod club that I have been researching that existed in California the late 1930s known as the "Hot Irons" club. Any info, photos, etc. will be greatly appreciated. If anyone has any personal information as to the whereabouts of original members who might still be alive, please contact me with any info you might have. Thank you in advance for your help.
Contact: Jason - Email: cowboy76@comcast.net

My frame is bent from the rear motor mounts forward, about two inches to the left. Is there anyone in Northern California that is able to fix this frame. I would buy another one if I could find one. I live in the Sacramento area. Any help would be greatly appreciated.
Contact: Mike Long - 916-863-7417

Chassis with wheels & brakes preferably modified, ie: juice brakes, Zed, lowered front axle, V8 rear end do not need engine or tranny. Also searching for a McDowell valve cover for an overhead.
Contact: krmartin@redburd.com.

Side drive magneto adapter for my Model A engine. I have some sr winfield carb parts to offer in trade, partial, or just plain old boring cash. I would also like an aluminum side cover for my A engine. I know new is available but it would look out of place on my car, and I am hoping one with character will turn up . Thanks
Contact: Jared - Email: amsando@socal.rr.com

‘27 T truck roadster body, good firewall, new Speedway 4" chopped windshield with new safety glass, homemade dash with working speedo, foamseat. The quarterpanels need patching but fair shape otherwise. Drivers door is tack welded shut. Floor is made out of 2 stop signs. Asking $1400.
Contact: chopperzhouse@sbcglobal.net.

Fresh batch of new V8 quickchanges now available.
Also have a few Model A ones left, Full details, prices, delivered to your door. Contact Kiwi Quickchanges, Derek Thomason, New Zealand. antiqueford@xtra.co.nz

Researching history of Exposition Park Raceway, San Luis Obispo 1922-1925: Seeking track information, photos, cars and drivers. Need any info on the following: Ed Winfield, Poverty Looking Special & Kant Skore; Eddie Meyer, Jr., Redlands Special; Harry Hooker, Hooker Special; as well as local drivers Fred Luelling, Fred Wallace, Harold Fredriksen, Johnnie Holmes. Also any other drivers who may have participated in the “West Coast Circuit” during the 1920s may be pertinent’
Lance Baumberger, San Luis Obispo, CA 805-0786-0936 or best to contact by email, baumbergerL@yahoo.com

New cast iron safety hubs keeps hub and drum on vehicle if axle breaks welds to rear hub). $90.00 set for two wheels. Cast Iron header performs same as computer tuned tube headers see Steve Serrs dyno test $ 225.00 complete kit. Hydraulic brake kits . Weber down draft kits. $475.00
Dave Wilton 530-872-0122 call after 12 noon pst

The HAVE/WANT page has been cleaned up, as per management, if any of the stuff that was removed is still for sale let me know and I will repost it